(866) 777-2590Mon–Fri 9AM–6PM PST
FAST + FREE Shipping on orders above $999 · Lifetime Returns

FAST + FREE Shipping on orders above $999 · Lifetime Returns

Outdoor Kegerator Guide: Built-In Beer Dispensers

An outdoor kegerator is a refrigerated keg cabinet with a tap tower, built with weather-resistant materials and approved by its manufacturer for use outside. Look for three things before you buy: the manufacturer’s outdoor rating and installation temperature range, a keg capacity that matches the beer you actually drink, and front venting if you plan to build it into an island. Below we cover each, plus CO2, installation and line cleaning, and compare the built-in beer dispensers we carry.

What “outdoor rated” means for an outdoor kegerator

An indoor kegerator on a patio faces heat, humidity and rain it was not designed for, and manufacturers such as Marvel apply warranties to outdoor operation only on models designed for outdoor use. Outdoor models use stainless steel cabinets and doors and refrigeration meant to hold temperature on a hot day.

“Outdoor rated” is still a manufacturer claim with limits, so read the documents for the exact model. For example, Marvel’s owner’s guide for its outdoor beverage dispensers gives a recommended installation location temperature range of 55°F to 100°F, and it says to winterize when the daily low reaches 38°F or below. It also states that running the unit below that winterization temperature voids the warranty. Coyote describes its 24 inch kegerator as built from 304 stainless steel for outdoor kitchens. If your inspector needs an outdoor safety listing, request it by model number before ordering.

Planning wine storage too? See our outdoor wine fridge guide.

What size keg fits in a kegerator?

The Brewers Association’s Draught Beer Quality Manual lists these common sizes:

  • Half barrel (full size keg): about 15.5 gallons.
  • Quarter barrel (pony keg): about 7.75 gallons.
  • Sixth barrel (sixtel): about 5.16 gallons. Handy for running two beers in one cabinet.
  • Cornelius (corny) keg: roughly 5 gallons, common with homebrewers. Corny kegs use ball lock or pin lock fittings instead of a commercial coupler.

Capacity varies between 24 inch models, so check the listing. Our Marvel 24 Inch Outdoor Single Tap Built In Beer Dispenser lists one half barrel, one quarter barrel, one slim quarter, two slim sixth barrels, or two Cornelius kegs (ball lock fitting not included). The U-Line OKR124 24″ Keg Refrigerator, by contrast, lists one standard quarter barrel, or one slim quarter plus one sixth barrel, and no half barrel.

Single tap vs dual tap kegerator

A single tap kegerator pours one beer at a time. It suits one house beer and leaves room for the largest keg the cabinet accepts.

A dual tap (twin tap) kegerator lets you pour two beers, or a beer and a cider or seltzer, at once. The catch is space: two kegs in a 24 inch cabinet means two smaller kegs, usually sixth barrels or corny kegs. Marvel’s manual notes that its double tower units can support two sixth barrels.

Marvel offers a Beer Single Tap Kit with CO2 Tank and a Beer Double Tap Kit with CO2 Tank, each listed with a Lo-Boy coupler, hoses, a 5 lb CO2 tank and a drain pan.

Kegerator CO2 tank basics

Beer kegerators push beer with CO2. The gas runs from the tank through a regulator, which lowers it to serving pressure, and then into the keg through the coupler. A few practical points from Marvel’s owner’s guide:

  • The tank always connects to the regulator, never directly to the keg.
  • A properly filled tank reads about 750 psi on the high pressure gauge.
  • Suggested serving pressures are roughly 12 to 14 psi for lagers and 9 to 12 psi for ales. Treat those as a starting point.
  • A 5 lb tank typically dispenses about 5 to 7 half barrels, or 14 to 21 sixth barrels, according to the same guide.

Marvel’s wine dispensers use nitrogen instead, so buy the kit that matches what you pour. Keep the tank upright and secured, and follow the regulator instructions.

On temperature, the Brewers Association recommends holding beer between 34°F and 38°F from keg to glass. Both Marvel models we carry have a digital control range of 34°F to 60°F, which covers that.

Built in beer dispenser vs freestanding

A built in beer dispenser slides into a cabinet opening in an outdoor kitchen island, flush with the surrounding doors. To do that it must breathe from the front. Marvel’s manual says ventilation is required from the bottom front of the appliance and that the front grille must not be blocked. A rear venting unit boxed into an island can overheat.

Freestanding units need open airflow around them. Some models allow either: the U-Line OKR124 listing says built in or freestanding. Marvel notes that its outdoor models with articulated hinges are intended for built in applications only, so check the hinge type and install guide before planning a rolling bar.

If the kegerator is part of a bigger build, our built-in grill and outdoor kitchen guide covers island layout, and our wine fridge vs beverage fridge comparison helps if you are deciding what goes in the bays next to it.

Power, installation and winterizing

Marvel calls for a grounded 115 volt, 15 amp dedicated circuit and warns never to remove the grounding prong. Its manual also notes that GFCI devices can cause nuisance tripping, while outdoor receptacles are usually required by local code to have GFCI protection. Have a licensed electrician run the circuit and reconcile the manual with your local code.

  • Measure the cutout against the manufacturer’s current install guide.
  • Plan for drainage. Marvel sells a Beer Drain Sump for built in installations of its beer cabinets.

When the season ends, or lows reach the temperature your manual names (38°F for Marvel), follow the winterizing steps: remove kegs, clean the lines, unplug, dry the interior and prop the door. Disconnect the CO2 tank and store it per its instructions.

Cleaning beer lines

Dirty lines can cause off flavors and poor pours. The Brewers Association recommends cleaning draught lines with a caustic line cleaner at least every two weeks (14 days), taking faucets apart and cleaning them on the same schedule, and descaling with an acid cleaner quarterly. Marvel’s manual says to clean the system between uses. Homebrewers running corny kegs may also want a keg washer such as the Ss Brewtech Keg WaSsher.

Comparing our outdoor kegerator models

Specs below come from our product listings. Confirm cutout dimensions with the manufacturer’s install guide before building.

Model Taps Keg capacity (per listing) Temp range Install
Marvel 24″ Outdoor Single Tap 1 1 half, 1 quarter, 1 slim quarter, 2 slim sixth, or 2 corny 34°F to 60°F Built in
Marvel 24″ Outdoor Twin Tap 2 Same cabinet as single tap; two sixth barrels for two beers 34°F to 60°F Built in
Coyote 24″ Kegerator C124KEG 1 1/6, 1/4 or 1/2 barrel 32°F to 65°F Built in, front venting
U-Line OKR124 24″ Kit sold separately 1 standard quarter, or 1 slim quarter plus 1 sixth 34°F to 60°F Built in or freestanding

See the full lineup on our Marvel brand page, and visit the wine fridge buying guide for the rest of our beverage cooling guides. Orders of $999 or more ship freight free. Questions? Call 866-777-2590, Monday to Friday, 9AM to 6PM PST. Our return and refund policy is online. Enjoy your tap responsibly.

Frequently asked questions

Can I use an indoor kegerator outside?

It is not recommended. Indoor units are not built for outdoor heat and moisture, and warranties may not cover outdoor use. Choose a model its manufacturer approves for outdoor use.

What size keg fits in a kegerator that is 24 inches wide?

It depends on the model. Some 24 inch units take one 15.5 gallon half barrel or two sixth barrels; others take a quarter barrel at most. Check the keg capacity on the listing.

Is a single tap or dual tap kegerator better?

Single tap suits one house beer in a large keg. Dual tap suits variety, usually with two sixth barrels or corny kegs in the same cabinet.

Does a kegerator come with a CO2 tank?

Not always. Some include a tap kit and tank; others sell them separately. Marvel’s single and double beer tap kits each list a 5 lb CO2 tank.

Does an outdoor rated kegerator need a dedicated circuit?

Follow the manual. Marvel specifies a grounded 115 volt, 15 amp dedicated circuit. Use a licensed electrician.

Leave a Comment

Your email address will not be published. Required fields are marked *

✓ Authorized dealer for 200+ brands✓ Free shipping over $999✓ Lifetime return window✓ US-based support, Mon-Fri 9-6 PST✓ Secure checkout
Secure Site256-bit SSL encrypted
Safe CheckoutYour details stay private
Authorized Dealer200+ brands, factory-direct
Scroll to Top