A drop in cold food well is a refrigerated (or ice-filled) pan well that sits inside a cutout in your counter, so salads, toppings and deli items stay cold right where staff build plates or guests serve themselves. Choosing one comes down to four things: how many full-size pans you need across, whether you want mechanical refrigeration or ice, the counter cutout and cabinet space under it, and the power and drain you can run to it. This guide walks through each one using the Hatco and APW Wyott models we carry.
How a drop-in cold food well works
The well is an insulated stainless liner with a condensing unit hanging below the counter. On a refrigerated cold well, cold wall construction chills the sides of the well, and the pans sit in the chilled space. Hatco is clear that its wells are made to hold food that is already cold, not to cool it down: the spec sheet says the well “keeps prechilled food products at safe serving temperatures.” Pre-chill everything in your walk-in or reach-in first, then load the well.
The target is the same for any cold holding equipment. The FDA Food Code requires cold time/temperature control for safety (TCS) food to be held at 41°F or below, as summarized in this Institute of Child Nutrition cold holding fact sheet, and the FDA’s own Food Code section 3-501.17 document refers to ready-to-eat TCS food “held at a temperature of 5°C (41°F) or less.” Your local health department enforces its own adopted version, so check with them.
Cold well pan sizes and capacity
Drop-in wells are sold by how many full-size openings they have. A full-size food pan is 12 x 20 inches, and fractional pans (1/2, 1/3, 1/6 and so on) are sized to divide that same opening, so three 1/3 pans or six 1/6 pans take the place of one full-size pan when you use adapter bars. Hatco ships its CWBP wells with pan support bars for full-size pans and lists full-size pans in 2.5, 4 and 6 inch depths as accessories.
How to size it:
- Count the items you serve cold at once, then decide pan size per item. High-volume items (lettuce, a house salad) earn a full or 1/2 pan; garnishes and dressings fit in 1/6 pans.
- Pick depth by turnover. Shallow 2.5 inch pans hold less but cycle faster; 4 and 6 inch pans need fewer refills. Deeper food is harder to keep evenly cold, so do not overfill above the pan rim.
- Measure the counter run first. A three-pan Hatco CWBP-3 is 45 inches wide overall; the five-pan CWBP-5 is 71 inches.
Refrigerated cold well models compared
These are the drop-in refrigerated cold wells on our site with the specs we could confirm from the listing or the manufacturer spec sheet. Prices were listed as shown when we checked in October 2026.
| Model | Pan capacity | Counter cutout (W x D) | Electrical (120V) | Listed price |
|---|---|---|---|---|
| Hatco CWBP-S1 (slim) | 1 full-size, placed lengthwise | 25.22 to 26.06 in x 17.06 to 17.94 in | 1/5 HP, 345 W, 5.2 A | $4,420.90 |
| Hatco CWBP-3 | 3 full-size | 43.125 to 44 in x 25.19 to 26 in | 1/5 HP, 345 W, 5.2 A | $5,077.60 |
| Hatco CWBP-4 | 4 full-size | 56.125 to 57 in x 25.19 to 26 in | 1/3 HP, 440 W, 6.5 A | $5,524.75 |
| Hatco CWBP-5 | 5 full-size | 69.125 to 70 in x 25.19 to 26 in | 1/2 HP, 560 W, 9.3 A | $5,840.45 |
| APW Wyott RTR-4DI | (4) 1/6 size pans | Ask us for the spec sheet | 1/6 HP motor | $2,684.00 |
Hatco figures come from the Hatco CWBP spec sheet and the CWBP-S slim spec sheet. All the CWBP models use R-290 refrigerant, have a 1 inch brass drain, plug into a NEMA 5-15P receptacle at 120V and are NSF 7 approved; Hatco’s product page also lists UL and cUL certification for refrigeration equipment. Confirm every cutout dimension against the current drawing before you cut. You can browse the full lineup on our Hatco brand page.
Which one fits your counter
- Hatco CWBP-S1: a slim, one-pan well with a shallower footprint (about 19 inches deep overall versus 27 inches on the standard CWBP), useful on narrow counters or behind a sneeze guard where reach matters.
- Hatco CWBP-3, CWBP-4 and CWBP-5: the standard choice for salad bars, sandwich lines and buffet runs. Note that amperage climbs with size, so the CWBP-5 at 9.3 A should get its own circuit if your electrician agrees.
- APW Wyott RTR-4DI: a self-contained, cULus-certified unit for four 1/6 pans with hinged removable covers. It suits a topping or condiment station rather than a full cold line.
Ice cooled vs refrigerated cold well
An ice-cooled well is an insulated liner with a drain: you fill it with ice, nest the pans in the ice and drain the meltwater. It needs no electrical work and costs less up front, but staff must keep the ice topped up through service, and temperatures drift as the ice melts. A refrigerated cold well holds a set temperature on its own and needs no ice handling, but you pay for the condensing unit, a power circuit and ventilated cabinet space.
For a kitchen running a cold line all day, a refrigerated well usually saves labor. For a seasonal or occasional buffet, ice can be enough. Hatco even sells false bottoms for the CWBP that it says allow better drainage for units that hold ice. Do not confuse either type with a hot food well: the Atlas Metal WIH-4 drop-in on our site, for example, is a heated well (208V, 20A, 6-30P plug), not a cold well.
How to install a drop-in cold well
Installation is a job for your contractor, electrician and plumber. These points from Hatco’s CWBP installation and operating manual show what to plan for:
- Cut the counter to the published cutout range. The counter must be level and reinforced if needed to carry the unit plus full pans.
- Seal the rim to the countertop with NSF-approved silicone sealant (or order the factory gasket option). If condensation forms under the counter, Hatco suggests polyurethane foam sealant in the gap.
- Ventilate the cabinet. Hatco calls for at least 7 inches between the condensing unit and any combustible or interior cabinet surface, plus 12 x 12 inch louvered or grill openings for intake and exhaust. Room temperature should stay between 65°F and 86°F.
- Run the drain from the 1 inch fitting to a trap and drain line per local plumbing code, or use a catch pan that is emptied regularly.
- Provide power: a grounded receptacle of the right voltage and plug type, within 6 feet of the control panel.
Hatco’s manual gives a factory setpoint of 39°F and says to let the well run about 60 minutes before loading food. Always hold food in pans, never directly in the well. If you are planning a full line, our range hood CFM guide covers the ventilation side of the kitchen, and our griddle vs grill comparison helps if the cold well sits next to a cooking station.
Frequently asked questions
What temperature should a drop-in cold food well hold?
The FDA Food Code calls for cold TCS food at 41°F or below. Hatco’s CWBP ships with a 39°F setpoint. Load only pre-chilled food and check pan temperatures during service.
What size pans fit a refrigerated cold well?
Wells are rated in full-size 12 x 20 inch openings. With adapter bars, each opening can take fractional pans such as 1/3 or 1/6 sizes, typically in 2.5, 4 or 6 inch depths.
Does a drop-in cold well need a drain?
The Hatco CWBP models have a 1 inch brass drain for cleaning and condensation, which should be plumbed to a trap and drain line or a catch pan per local code.
Get help choosing a cold well
A drop-in cold food well is a long-term part of your counter, so match the cutout, power and pan layout before you order. For the rest of your line, see our commercial kitchen equipment guide. Every model above qualifies for free freight shipping on orders of $999 or more, and our team can pull spec sheets or answer sizing questions at 866-777-2590, Monday to Friday, 9AM to 6PM PST. Review our return and refund policy before ordering.
