VintageView Vino Pins installation is a one-afternoon job for most people: two small metal pins per bottle, a level, a drill and the right anchors for your wall. The details that decide whether the display looks crisp and stays put are the spacing between the neck pin and base pin, the spacing between rows, and whether each pin lands in a stud or in drywall. This guide walks through the process using VintageView’s own Vino Pins with Collars installation instructions and the specs on our product pages.
How many Vino Pins per bottle?
Each bottle sits on a pair of pins: a base pin that cradles the body of the bottle and a neck pin that holds the neck. The Vino Pins 1 set is one pair for one 750 ml bottle, displayed label-forward. To go deeper, you add extensions to the same pair rather than drilling new holes:
| Product | Bottles per pair | Size with bottles (H x W x D) | Price |
|---|---|---|---|
| Vino Pins 1 | 1 (750 ml) | 5 x 13 x 4 in | $21 |
| Vino Pins 2 | 2 (750 ml) | 5 x 13 x 8 in (8.5 in with collars) | $39 |
| Vino Pins 3 | 3 (750 ml) | 5 x 13 x 12 in (12.5 in with collars) | $56 |
| Vino Pins 1 Acrylic | 1 only | 5 x 13 x 4.5 in | $22 |
| Vino Pins Mag 1 | 1 (1.5 L or Champagne) | 5 x 15 x 4 in | $21 |
The Vino Pins Extension threads onto an installed pin and adds 4 in of depth and one bottle. VintageView allows up to two extensions per pair for 750 ml bottles, so three deep is the maximum. Acrylic pins are single-depth only and do not take extensions.
Tools and parts for Vino Pins installation
VintageView’s starter kit instructions list these parts: one neck pin, one base pin, two collars, two toggle bolts, two machine/lag studs and a hex key. You will also need:
- A level and a pencil or awl
- A drill with a 5/32 in (4 mm) bit for pilot holes
- A 5/8 in (15.9 mm) bit for the toggle bolt holes in drywall
- Two 10 mm wrenches (or adjustable wrenches) for stud mounting
- A stud finder, which is not on VintageView’s list but saves guesswork
If you are installing into drywall, choose the Collars option or add Vino Series Drywall Collars. VintageView’s instructions say all drywall installations require collars, and the drywall or wood must be at least 1/2 in thick. For walls that do not meet that, VintageView says to contact your supplier for the right hardware before drilling.
Wine pegs installation, step by step
- Pick the neck direction. Decide whether bottle necks point left or right. If necks point right, the base pin goes to the left of the neck pin, and the other way around. Keep the whole wall consistent unless you are deliberately mixing directions.
- Mark the holes. Tape the printed template to the wall, level it along its long edge, and mark the two holes for your chosen direction. VintageView notes that for magnum (1.5 L) bottles, the horizontal distance between the neck and base pins increases by 1 in to 8-1/2 in, which puts the standard 750 ml spacing at 7-1/2 in.
- Drill pilot holes. Use the 5/32 in bit at each mark. If you hit wood, you have found a stud; use the stud method below. If you do not, open the hole to 5/8 in for the toggle bolt.
- Prepare the toggle bolts. Thread the wing nut on so the wings fold away from the bolt head, run it to the head, then back it off about one full turn so the wings can open freely.
- Assemble and install. Slide a collar onto the bolt, thread the pin on, push the bolt through the drywall until the collar sits flush, gently pull back to seat the wings, and hand-tighten the pin clockwise. Install the base pin in the lower hole first, then the neck pin in the upper hole.
Mounting Vino Pins into studs or wood
When a pilot hole lands in a stud, VintageView’s method is to drive the machine/lag stud into the hole until the coarse lag threads disappear, leaving only the fine threads exposed. Lock two nuts together on the fine thread and use a wrench on the outer nut to drive it if your kit does not use the hex key. Then slide a collar over the stud and thread the pin on by hand. Our guide to wine rack installation into studs vs drywall anchors explains when each approach makes sense.
Spacing: how to lay out a wine peg wall
Each bottle needs a footprint of about 5 in high by 13 in wide on the wall, according to the Vino Pins 1 dimensions. That gives you a simple planning grid:
- Rows: plan about 5 in per row. VintageView’s Vino Pins Flex 45 column fits 9 bottles in 45 in of height, which works out to the same 5 in per bottle.
- Columns: plan about 13 in per column for 750 ml bottles, or 15 in for magnums.
- Depth: plan 4 in off the wall for single-deep, about 8.5 in for double and about 12.5 in for triple, adding the collars where used.
If you would rather not plot every hole, the Vino Pins Designer Grid 3×1 includes three pin sets, collars, hardware and a 36 in wide printed plotting guide, and larger 3×2 and 4×3 versions are available. For a vertical column with less drilling, the Vino Pins Flex 45 mounts pins to two steel strips that can hang straight or tilt up to 45 degrees.
Wine pegs for walls you cannot drill much
Tile, glass and thin paneling are where people get stuck. VintageView’s floating Post system is one answer: the Vino Pins Reveal kit uses a 5 ft steel post that holds bottles 2 in off the wall on two standoff brackets, so you drill for the brackets instead of every pin. Post-system pins are sold without wall hardware because they mount to the post. Our page for those pins lists mounting plate spacing starting at 5 in.
Care after installation
VintageView recommends checking the pins regularly for tightness and hand-tightening any that loosen. If the wall surface around a pin shows signs of breaking, stop using that spot until the wall is repaired. Clean pins with a damp cloth and mild dish soap; alcohol-based cleaners, including many glass cleaners, and abrasive pads can damage the finish.
Need help planning a wall? Our guide to how many bottles fit on a wine wall helps with capacity, and the wine rack and cellar storage guide covers the wider options. Browse everything on our VintageView brand page, or call 866-777-2590, Monday to Friday, 9AM to 6PM PST.
Frequently asked questions
How many Vino Pins per bottle do I need?
One pair, a neck pin and a base pin, for each bottle position on the wall. A single pair holds one to three 750 ml bottles depending on how many extensions you add.
Can Vino Pins go straight into drywall?
Yes, with drywall collars and toggle bolts, into drywall at least 1/2 in thick. VintageView’s instructions say all drywall installations require collars.
What is the spacing between the neck and base pin?
VintageView says magnum spacing is 1 in wider than standard, at 8-1/2 in, which makes the standard 750 ml spacing 7-1/2 in. Always use the printed template that comes with the pins.
How far apart should rows of wine pegs be?
Plan about 5 in per row, based on the 5 in height of a Vino Pins 1 with a bottle stored and the 9 bottles in 45 in of the Flex 45 column.
Can I add depth later?
Yes. Extensions thread onto installed metal pins at any time, up to three bottles deep for 750 ml bottles. Acrylic pins stay single-depth.
